Circuit boards with lights in epoxy within a deskCircuit board desk in ten techniques Step one The theory.Placing boards like these in epoxy inside a desk ..but....what table? eventually I discovered this table on line the trendy metal legs will go properly With all the boards Action 2 Planning.the Wooden of the aged desk was discolored as well as the steel was filthy so with paint stripper I eradicated outdated layers of varnish (I made use of a scrape card for that) And that i cleaned the metal the backs of the boards had to be definitely flat first I attempted to get rid of components which has a soldering iron but the speediest way was with pliers Step three Creating place.mmm..how would I be Placing the boards in? I indicate, in what shape? I chose the simple strip shape I Lower that shape to depth Along with the saw ..to about 25 mm I took out a 25 x four grid While using the router the remaining blocks, I chiseled out huge pieces Using the grain on the Wooden The remainder sideways and immediately after cleaning it was Prepared for..Action 4 Placing the boards in.I did not need to see any wood from the smaller spaces close to the boards so I put Within this aluminium tape then it had been simply a puzzle in this article and there I needed to ....force a board down that has a screw as the Center identify of my workshop ....is 'dust' ..I figured I'd for making a tent prior to pouring epoxy Phase five Producing a tent.nothing at all fancy, just two tent-formed finishes connected by Wooden on the edges strips ....lined with rubbish bags some boards ended up however free for the following phase they needed to be set so this was the 1st pour with epoxy last opportunity to place the boards Move 7 Placing during the LEDs (which might be no longer LEDs :-) I wished lights to light up but with no electric power ..no cables or batteries ..nah ..so I thought of fiber optic cable And that i took a traditional LED drilled a hole in The underside broke from the wires ..and caught a fiber cable in then I drilled holes during the boards and trapped the (glued) fibers In this particular block by using a gap ..may be the point of interest with the fiber cables I pulled the fibers by means of ....glued them in ....and Minimize them off funny: you'll be able to see the colors on the LEDs just to make certain ..I poured within the LEDs so far, so very good ..on to ..Step 8 The massive Pour.witness ..the pouring of ..seven liters epoxy the epoxy uncovered ..the table is bent in the middle so I had to pour further at the edges Stage 9 Sanding don't ask me why ....but I recorded every one of the sanding so now I am aware ....it took me a complete of 2.5 several hours with sixty, a hundred, 180 and 320 grit Move 10 End the initial system was ....to sand and polish the epoxy instead I decided to pour an additional layer I will demonstrate later on why I sanded the wood one particular very last time and gave it some coats of Danish Oil << Completed! >> The End Result Epilogue So? Achievement or Fail? very well, reverse of what you may think immediately after looking at this video clip the table was a are unsuccessful What? Why? Someplace in the procedure, and I'm not exactly certain wherever, the epoxy received not blended perfectly sufficient.That resulted in sticky tender places and really unsightly places wait, allow me to demonstrate you Couldn't or not it's repaired? that's why I attempted to put A further layer in excess of it all - what you just noticed within the 'finish'-part of the video but that did not aid whatsoever there were a lot of comfortable places at the sides, the sticky epoxy retained crawling up and out so not only had been there unpleasant places Inside the epoxy, the table staying forever sticky, created it pretty much as good as ineffective Bummer! Yeah, I had been very upset by this, since 95 percent with the epoxy is okay and it is extremely wonderful to think about the lots of facts with the circuit boards also to Participate in Using the lights What now? properly, I suppose I have to just take my reduction and find out it like a Studying matter What's going to you do Along with the desk? I am not sure nonetheless.I'll hold it for now and think about it.seriously finding it correct would mean for making an extra groove at the edges, concerning the Wooden and the epoxy, by using a router or possibly a observed and chisel the unsuccessful epoxy out that may be a lot of function, so ..I suppose I'll sleep on it for a while Although the table might not be an entire accomplishment, just it's possible you realized a little something in the video, Or possibly you found the movie entertaining.If you favored the video clip (not the table) make sure you such as the movie and subscribe on the channel.See you within our subsequent video!.